1602 – PRM-25 LED Error Code Messages
Applicable to:
PRM 25
| Error Code Messages | Power LED | Ready LED |
| Over temperature | 3 blinks | Off |
| G794 fail | 4 blinks | 4 blinks |
| T1 fail | 4 blinks | 5 blinks |
| Lamp error | 5 blinks | Off |
| Ballast over temperature | 5 blinks | 1 blink |
| Ballast short circuit in output detected | 5 blinks | 2 blinks |
| End of lamp life detected | 5 blinks | 3 blinks |
| Ballast lamp did not ignite | 5 blinks | 4 blinks |
| Lamp extinguished during normal operation | 5 blinks | 5 blinks |
| Lamp extinguished during run-up phase | 5 blinks | 6 blinks |
| Lamp memory write error | 5 blinks | 7 blinks |
| Lamp memory write buffer overflow | 5 blinks | 8 blinks |
| Lamp UART buffer overflow | 5 blinks | 9 blinks |
| Lamp current calculation error | 5 blinks | 10 blinks |
| Lamp corrupted software configuration | 5 blinks | 11 blinks |
| Lamp voltage too low | 5 blinks | 12 blinks |
| Lamp FLASH memory CRC error | 5 blinks | 13 blinks |
| Lamp EEPROM memory CRC error | 5 blinks | 14 blinks |
| Lamp EEPROM configuration does not match FLASH kernel | 5 blinks | 15 blinks |
| Buner fan | 6 blinks | 1 blink |
| Lamp fan | 6 blinks | 2 blinks |
| Power fan | 6 blinks | 3 blinks |
| DMD fan | 6 blinks | 4 blinks |
| Lamp door open | 7 blinks | Off |
| DMD error | 8 blinks | Off |
| Color wheel error | 9 blinks | Off |
In the event of an error, please disconnect the AC power cord and wait for one minute before restarting the projector. If the POWER or LAMP LEDs are still blinking or the TEMP LED is lit, contact Promethean Technical Customer Support.
Related Articles
1598 – PRM-45 LED Error Code Messages
Applicable to: PRM 45 A Error Code Messages Power LED Lamp LED Temp LED System initial Flash Off Off Ready to power on (Standby) On Off Off System power on Flash Off Off Lamp lit, system stable On Off Off Cooling Flashing Off Off Over temperature Off ...1599 – PRM-35 and PRM-32 LED Error Code Messages
Applicable to: PRM 32 PRM 35 Error Code Messages Temp LED Power LED Lamp LED Ready to Power on (Standby) Off On Off System Power on Off Blinks Off Cooling Off Blinks Off Over temperature On Off Off Thermal break sensor error Off 4 blinks Off Lamp ...1601 – EST-P1 LED Error Code Messages
Applicable to: EST P1 Error Code Messages Warning LED Lamp LED Power LED Power on Off Off Blue Power off Off Off Orange Lamp fail Off On Off Cooling Off Off Flashing Over temperature On Off Off T1 error Off 1 blink 3 blinks T2 error Off 2 blinks 3 ...1600 – UST LED Error Code Messages
Applicable to: UST P1 UST P2 Error Code Messages Temp LED Lamp LED Power LED Power On Off Off Green Power Off Off Off Green Cooling Off Off Flashing Over temperature On Off Off Thermal break sensor error Off Off 4 blinks Lamp error Off On Off Fan 1 ...1436 – PRM-25 RS232 control code commands
Applicable to: PRM 25 The commands below should only be used by users who are familiar with using this method of operation. Promethean’s support is limited to the commands outlined below. RS232 Setting Minimum delay for next command: 1ms Control ...